产品介绍

梨树园外墙腻子粉独家采用中和技术，以无机胶凝材料为基材，配以黏结材料及其他助剂精细加工而成。将腻子粉碱性降到最低限度，有效降低墙面漆发花、泛碱现象。双向粘性好，高拉神强度控制裂纹，柔韧抗裂，施工性能卓越，具有良好的填充性、耐水性!

LiShu Yuan external wall putty powder exclusive use of neutralization technology, inorganic cementitious material as the base material, with the adhesive material and other additives fine processing. The putty powder alkalinity to a minimum, effectively reduce the wall paint flower, alkali phenomenon. Good two-way viscosity, high strength control crack, flexible and cracking, excellent construction performance, with good filling, water resistance!

性能特点

低碱性，有效展示乳胶漆原本的色彩;

双向粘性好，高拉伸强度控制裂纹、柔韧抗拉裂;

具有良好的填充性、耐水性;

适用室外墙面找平，施工性能卓越。

Low alkalinity, effectively displaying the original color of latex paint.

Two way sticky, high tensile strength control crack, flexibility and anti cracking;

It has good filling and water resistance.

It is suitable for outdoor wall surface leveling, and its construction performance is excellent.

使用方法

施工前请确认基层必须坚实、平坦、无油污、浮灰等物。脱皮、粉化及空鼓部份必须剔除，表面过干燥的基层，应先喷少量清水润湿后再施工。

刮涂方法一般按照自上而下，从左到右的顺序进行操作，力求均匀不漏底，不留接缝痕迹。

腻子刮涂不可过厚，第一道以找平为准，一般刮涂三遍。第一遍略大于后面两遍的用料量，待干燥后，打磨处理进行墙面漆施工。

Before construction, please confirm that the base must be solid, flat, oil free and float ash. The peeling, powderi-ng and hollowing must be removed. The surface of the dry base should be sprayed with a little water before wetting.

The scraping method is generally operated from top to bottom, from left to right in order to keep the bottom even and no seam marks.

The putty can not be scraped too thick. The first is leveling. It is usually scraped three times. The first time is sligh-tly larger than the latter two times of the amount of material, after a little dry, grinding treatment for wall paint construction.

用量及注意事项

基面平整的情况下约2.5-3KG/m²。

按1：0.4(粉：水)的比例混合搅拌均匀后即可使用(加水量可根据施工要求进行适当增减)。配制好的浆料应在2小时内用完。

本产品无味、无辐射、符合环保要求。

本品施工后12小时内避免雨淋及霜冻。

木质板材不宜直接施用本品，建议使用界面剂处理或其它柔性底涂腻子后再行施用本品。

When the base surface is flat, it is about 2.5-3KG/m.

Mix and mix evenly according to the ratio of 1:0.4 (po-wder: water) and then use it (the amount of water can be increased or decreased according to the construction requirements). The prepared slurry should be used up in2 hours.

This product is tasteless, non radiation.

Rain and frost are avoided within 12 hours after the construction of this product.

It is not suitable for wood products to be directly applied to the product. It is recommended to use the interface agent or other flexible bottom coating putty before applying this product.