logo
这是描述信息
产品中心
您现在的位置:
首页
/
/
/
氟碳腻子粉(LSY-W-1002)

产品中心

产品中心

PRODUCT

全部分类
描述

产品介绍

氟碳腻子粉是以高分子材料与胶凝材料为主要原料,配以各种专用助剂研制而成的一种专用腻子产品。

Fluorocarbon putty powder is a kind of special putty product, which is made of polymer material and cementitious material as the main raw materials and is matched with various special additives.

 

性能特点

优异的防水、抗渗性能,有效防止墙体内的碱性物质渗出;

柔韧性是常规单组份腻子的3-5倍,可遮盖墙体上的细微裂纹(结构性开裂除外);

优良的耐水、耐候性,彻底杜绝起皮、剥落、粉化等现象出现,延长涂饰工程的寿命;

粘结力超强,有效节省施工时间;

良好的亲和性,使墙体及涂料的底层具有良好的粘结力;

本产品分粗、细腻子,粗腻子用于基面找平,一般2-3遍,细腻子用于面层的刮平,一般3-4遍。

Excellent waterproof and impermeability, and effectively prevents the seepage of alkaline substances in the wall.

Flexibility is 3-5 times that of conventional single component putty, which can cover fine cracks on walls (except structural cracking).

Excellent water resistance and weather resistance, completely eliminate the phenomenon of peeling, peeling and powdering, and prolong the service life of finishing works.

The adhesive force is super strong, which effectively saves the construction time.

This product is divided into coarse, fine, coarse putty for the base level, generally 2-3 times, fine for the surface scraping, generally 3-4 times.

 

使用方法

墙面预处理:1-墙面应平整结实,无空鼓,无浮尘,无油脂、无污染、无混凝土养护剂等物。2-如墙面有凹槽或凸起,可先用水泥砂浆补平或用铲刀铲平。3-新批刮的墙面需待砂浆干硬后(最少十五天以后)才能刮腻子。

刮腻子:用刮刀将胶浆抹于墙面上,然后用刮刀将胶浆批刮平整,根据平整度的要求,批刮1-3遍,每遍时间间隔不应小于4小时,总厚度在1-2毫米之间。

打磨:刮完最后一遍腻子后的隔日即可打磨,注意控制打磨时机,时间越长,腻子越硬,就越难打磨。

清除灰尘:使用抹布、吸尘器将腻子表面的灰尘彻底清除,才能进行后续涂刷施工。

Wall pretreatment: 1 - The wall should be smooth and solid, no empty drum, no floating dust, no oil, no pollution, no concrete curing agent and so on. 2- if there are grooves or bumps on the wall, it can be leveled with cement mortar or leveled with a shovel. The new wall of 3- must be dry after mortar (at least 15 days later) to scrape the putty.

Scraping putty: apply the glue on the wall with a scra-per, then use the scraper to smooth the slurry. According to the requirement of the evenness, the scraping is 1-3 times. The thickness of the scraping is 0.5-1.0 millimeter each time. The interval of each time should not be less than 4 hours, the total thickness is between 1-2 millime-ters.

Grinding: After the last time the putty can be polished the next day, pay attention to control the timing of grinding, the longer the time, the harder the putty, the more difficult to grind.

Dust removal: the use of rags, high-pressure water guns or vacuum cleaners will be putty surface dust thor-oughly removed before the follow-up brushing constru-ction.

 

用量及注意事项

视基面的平整度,正常用量为1.5KG/遍。

本品阴凉干燥处储存,严禁受潮,未开封产品的保质期为6个月。

施工温度为5-30℃,空气相对湿度80%,无雨天环境下施工(热天施工注意养护,以免烧坏)。

本品施工后12小时内避免雨淋及霜冻。

When the base surface is flat, it is about 1.5-2KG/m.

This product is stored in a cool and dry place. It is stric-tly prohibited to be dampened. The shelf life of unopen-ed products is 6 months.

The construction temperature is 5-30 degrees, the rel-ative humidity of the air is 80%, and the construction is not in rainy days. Rain and frost are avoided within 12 hours after the construction of this product.

未找到相应参数组,请于后台属性模板中添加

联系我们

公司地址:湖南省怀化市中方县工业园
联系电话:0745-8132888(销售)       
0745-8666755 (销售)
电子邮箱:451768282@qq.com(销售) 

湖南梨树园涂料有限公司版权所有 湘ICP备16010882号   网站建设:中企动力长沙

二维码

关注官方微信号,
了解更多梨树园涂料

友情链接

涂料、防水材料、保温涂料、绝缘陶瓷材料、
水泥外加剂、墙体保温材料、
水漆的生产及批发销售