logo
这是描述信息
产品中心
您现在的位置:
首页
/
/
/
墙体专用保温腻子(LSY-BX-104)

产品中心

产品中心

PRODUCT

全部分类
描述

产品介绍

本品主要是以空心微珠、保温母料为骨料,配以胶粉、抗裂纤维、水泥、石英砂等材料组成的复合型建筑节能材料。主要用于外墙体需要做保温的工程,与保温隔热反射涂料配套使用,能有效提高整体保温系统的保湿功能,产品分为 厚批型与薄批型,厚批型主要屁股啊是一次性能平衡1-1.5公斤粉墙面,二薄批型则只能批刮0.5公斤左右,从保温的导热系数上厚批型优于薄批型。

This product is mainly composed of hollow microspheres, thermal insulation masterbatch as aggregate, rubber powder, crack resistant fiber, cement, quartz sand and other materials. Mainly used for exterior wall thermal insulation projects, and heat insulation reflective coatings matching use, can effectively improve the overall thermal insulation system moisture retention function, products are divided into thick batch type and thin batch type, thick batch type of main buttocks is a one-time performance balance of 1-1.5 kilograms of powder wall, two thin batch type can only scrape about 0.5 kilograms, from the thermal conductivity of heat preservation, thick batch type is better than thin batch type.

 

适用范围

主要用于建筑外墙隔热保温,配套建筑反射隔热涂料使用。

It is mainly used for building external wall thermal insulation, supporting building reflective thermal insulation coating use.nd energy-saving renovations for existing buildings.

 

使用方法

◆ 厚批型保温腻子:

保温腻子的水灰比腻子:水=1::065左右,在搅拌保温腻子时打浆料比正常腻子稍微稀点,打好后静置3-5分钟,让保温腻子内的颗粒充分吸收水分,再用搅拌机搅拌1分钟左右,充分让腻子吸水均匀,避免上墙时腻子出现较干而不好施工,施工时用小平板上浆到墙面上,跟着用大板托平,压实,如施工要求在2cm及以上厚度,尽量做2次批刮,且每次批刮需等待第一遍硬化后2天批刮,批刮太急会产生裂纹及批刮第二遍出现翻皮等现象,厚批型理论用量1cm厚用料约7.5kg/m2。

◆ 薄批型保温腻子:

薄批型保温腻子的水灰比腻子:水=1::045左右,搅拌方法与普通腻子相同,批刮保温腻子的厚度不要一次超过0.5cm,批刮腻子的方法与普通腻子相同,保温腻子理论用量0.5cm厚用量月5kg/m2,kehu在使用时建议使用厚批型,厚批型的导热系数会低于薄批型的。

◆hick batch thermal insulation putty:The water-cement ratio of thermal insulating putty is about 1:065. When mixing thermal insulating putty, the beating material is slightly thinner than normal putty. After beating, the granules in thermal insulating putty can absorb water sufficiently for 3-5 minutes, and then mix with a mixer for about 1 minute to make the putty absorb water evenly, so as to avoid putty being drier and not easy to construct. In construction, the putty is pasted onto the wall with a small plate. Following with large plate flattening, compaction, if construction requires thickness of 2 cm or more, try to do batch scraping twice, and each batch scraping needs to wait for batch scraping 2 days after the first hardening. If batch scraping is too rapid, cracks will occur and the second batch scraping will appear skinning phenomenon. The theoretical amount of material used for thick batch is about 7.5 kg/m2.

◆Thin batch heat preservation putty:The water-cement ratio of thin batch heat preservation putty is about 1:045. The mixing method is the same as that of ordinary putty. The thickness of batch heat preservation putty should not exceed 0.5 cm at one time. The batch heat preservation putty is the same as ordinary putty. The theoretical dosage of 0.5 cm thick putty is 5 kg/m2 per month. Kehu suggests using thick batch type when using it. The thermal conductivity of thick batch type is lower than that of thin batch type.

未找到相应参数组,请于后台属性模板中添加
上一个
下一个

联系我们

公司地址:湖南省怀化市中方县工业园
联系电话:0745-8132888(销售)       

     0745-8666755 (销售)
电子邮箱:451768282@qq.com(销售) 

 

湖南梨树园涂料有限公司版权所有  

湘ICP备18023106号  

本网站已支持ipv6访问         

网站建设:中企动力长沙

二维码

关注官方微信号,
了解更多梨树园涂料

友情链接

涂料、防水材料、保温涂料、绝缘陶瓷材料、
水泥外加剂、墙体保温材料、
水漆的生产及批发销售