产品介绍

该腻子是高分子聚合物配以填充粉料，经过中和技术，专门针对内墙乳胶漆施工而研发的一款新型腻子。腻子细腻光滑、粉体强度中，柔性不脆裂，且不含任何碱性物质，最大强度的抗碱，有效保障墙面漆不泛碱发花，该腻子不含甲醛、苯等有害物质，在其它性能上已大大超过了国家标准。公司一直遵守对客户负责，就是对自己企业负责的原则，在腻子粉生产时全部采用脉冲式大设备生产，并在原料上全部用正宗方解石材料，在原料和设备上杜绝了重金属污染，是目前最环保的腻子产品，并且打磨性能优异，打磨后生成的粉尘不会对人体造成很大影响(过去的碱性腻子打磨后会造成眼睛烧伤、红肿，并且对咽喉刺激很大)。

The putty is made of high molecular polymer and filling powder. After neutralization and technology, it is specially designed for filling the wall of interior wall latex paint. The putty is delicate, smooth, flexible and non-fragile in powder strength, and does not contain any alkaline substances. The greatest strength of the putty is alkali-resistant, which effectively protects the wall paint from alkaline blooming. The putty does not contain harmful substances such as formaldehyde and benzene, and has greatly exceeded other properties of the country. Home standard. The company has always adhered to the principle of being responsible to customers, that is, to its own enterprises. Putty powder is produced with impulse large equipment, and all raw materials are made of authentic calcite. Heavy metal pollution is eliminated in raw materials and equipment. It is the most environmentally friendly putty product at present, and its grinding performance is excellent. The dust generated after grinding will not have a great impact on human body. (In the past, alkaline putty can cause eye burns, swelling and irritation to the throat after polishing).

性能特点

柔性不脆裂，施工性能优异;

抗碱性能优异，避免墙漆泛碱发花;

无毒无味，绿色环保。

Flexible and brittle crack, excellent construction performance.

The alkali resistance is excellent, and the wall paint can be avoided with alkali and flower.

Innocuous and tasteless, green and environmental protection.

使用方法

施工基面保持结实、洁净、无油污及其它松散物。

水灰比约为1:3，以电动搅拌器搅拌成均匀、无粉粒的膏糊状，净置数分钟后再次搅拌一次，即可使用。

使用腻子抹刀将胶浆均匀地涂抹于基面上，一般涂抹2-3次，第二次涂抹必须在第一次涂面干燥后进行。最后一次涂抹完成后，视天气状况而定，在1-2天内可打磨，打磨时将刀痕轻轻磨平即可。

The construction surface should be solid, clean, oil-free and other loose matters.

According to the proportion of water in about 40%, the water is poured into the mixing bucket first, then the powder is added, and the paste is stirred by the electric mixer, and the paste without powder is mixed and stirred again for a few minutes, then it can be used.

Use a putty spatula to spread the glue evenly on the base surface, generally 2-3 times, the second coat must be dry after the first coat. After finishing the last coat, depending on the weather conditions, in 1-2 days can be grinded, grinding the knife mark gently smooth, do not grind to avoid affecting the strength.

用量及注意事项

基面平整的情况下约2-2.5KG/m²

本品阴凉干燥处储存，严禁受潮。

施工温度为5-30℃，空气相对湿80%(热天施工注意养护，以免烧坏)。

When the base surface is flat, it is about 2-2.5KG/m.

This product is stored in the cool and dry place, and it is strictly forbidden to be dampened.

The construction temperature is 5-30 degrees, and the air is relatively wet <80%.(Pay attention to maintenance in hot weather so as not to burn out)